肋角度对气膜冷却特性的影响

在光滑二次流通道的基础上,分析对比了两种带肋通道(135°肋和45°肋)对气膜冷却特性的影响.采用瞬态液晶测试技术获得了气膜孔下游表面传热系数比与气膜冷却效率分布.使用Fluent软件RANS数值方法对相应结构进行了数值模拟,并使用了realizable k-ε湍流模型.光滑二次流通道模型中,气膜孔内流线呈螺旋状分布,导致较大的孔内速度分离与流动损失.冷气射流分成两部分,其中一股形成一对偏斜的对转涡.135°肋结构中,二次流通道上部分的旋转涡为顺时针方向,使得气流易于流入气膜孔,气膜孔内流线呈直线分布.45°肋结构中,二次流通道上部分旋转涡为逆时针方向,增强了气膜孔内旋转涡.45°肋结构中冷气流入气膜孔之后的流动结构与光滑二次流通道结构相似.135°肋结构气膜冷却效率最大而表面传热系数比最低.     

Analysis of crack opening stresses for center- and edge-crack tension specimens

Accurate determination of crack opening stress is of central importance to fatigue crack growth analysis and life prediction based on the crack-closure model. This paper studies the crack opening behavior for center- and edge-crack tension specimens. It is found that the crack opening stress is affected by the crack tip element. By taking the crack tip element into account, a modified crack opening stress equation is given for the center-crack tension specimen. Crack surface displace- ment equations for an edge crack in a semi-infinite plate under remote uniform tension and partially distributed pressure are derived by using the weight function method. Based on these displacements, a crack opening stress equation for an edge crack in a semi-infinite plate under uniform tension has been developed. The study shows that the crack opening stress is geometry-dependent, and the weight function method provides an effective and reliable tool to deal with such geometry depen- dence.     

A theoretical model of semi-elliptic surface crack growth

A theoretical model of semi-elliptic surface crack growth based on the low cycle strain damage accumulation near the crack tip along the cracking direction and the Newman–Raju formula is developed. The crack is regarded as a sharp notch with a small curvature radius and the process zone is assumed to be the size of cyclic plastic zone. The modified Hutchinson, Rice and Rosengren(HRR) formulations are used in the presented study. Assuming that the shape of surface crack front is controlled by two critical points: the deepest point and the surface point.The theoretical model is applied to semi-elliptic surface cracked Al 7075-T6 alloy plate under cyclic loading, and five different initial crack shapes are discussed in present study. Good agreement between experimental and theoretical results is obtained.     

q悬臂式周向多自由曲面超精密加工工装卡具设计

针对周向全方位多自由曲面超精密加工过程中存在的问题,设计其专用卡具;通过模型分析,建立了确定卡具关键参数的数学公式,给出了保证多自由曲面相互位置精度的安装调试方法,为减小卡具部分的系统误差提供理论依据。     

水热-凝胶法ZrO2 气凝胶的制备与表征

以硝酸氧锆为锆源,尿素为凝胶促进剂,通过水热凝胶法结合超临界乙醇干燥,可成功制备出具
有良好纳米三维网络结构的ZrO2 气凝胶。采用透射电镜(TEM)、比表面积及孔隙度分析仪(BET),X 射线衍
射仪等测试手段对其结构进行了表征与测试。结果表明,ZrO2 气凝胶主要由无定型和四方晶相组成,其比表
面积为445 m2 / g,孔径主要分布在5 ~7 nm 和30 ~40 nm 两处。     

一种新型超宽带紧耦合天线阵列设计

针对紧耦合天线阵列（Tightly Coupled Array,TCA）安装于飞机、导弹、舰船等平台时接地板严重影响其阻抗带宽的问题,将栅格形阻性频率选择表面与交指型偶极子天线单元相结合,设计了一种新型多层结构的超宽带TCA。采用CST对加载与未加载栅格形阻性频率选择表面时TCA的性能进行了比较分析。结果表明：未加载时,受接地板影响其最佳阻抗带宽（VSWR〈2）为4．5：1（2．1～9．5GHz）;加载后,TCA可克服接地板的影响,其阻抗带宽可达10．4：1（1．8～18．8GHz）。     

基于BP神经网络的介质表面充电电位反演方法

为了实现全面、实时的在轨卫星充放电风险分析,基于在相同环境下,不同材料表面充电的关联性,利用BP神经网络建立了一种由Kapton材料表面充电电位反演卫星其他常用介质材料表面电位的模型。以Kapton材料的表面电位以及材料厚度为输入,其他介质材料的表面电位作为模型输出,使用COMSOL建立的表面充电模型对神经网络进行训练,将反演误差降低到10%以下,并利用Kapton与Teflon材料表面充电地面试验数据验证反演模型的准确性,结果显示Teflon表面电位的反演值与实测值间的相对误差小于16%。     

Morphology and Frictional Characteristics Under Electrical Currents of Al203/Cu Composites Prepared by Internal Oxidation

Two AhO3/Cu composites containing 0.24 wt.% A1203 and 0.60 wt.% A1203 separately are prepared by internal oxidation.Effectsof sliding speed and pressure on the fi-ictional characteristics of the composites and copper against brass are investigated and compared.The changes in morphology of the sliding surface and subsurface are examined with scanning electron microscope (SEM) and energy dispersive X-ray spectrum (EDS).The results show that the wear resistance of the AI203/Cu composites is superior to that of copperunder the same conditions.Under a given electrical current,the wear rate of AI203/Cu composites decreases as the AleO3-content increases.However,the wear rates of the Al203/Cu composites and copper increase as the sliding speed and pressure increase under drysliding condition.The main wear mechanisms for AleO3/Cu composites are of abrasion and adhesion;for copper,it is adhesion,although wear by oxidation and electrical erosion can also be observed as the speed and pressure rise.     

多轴加工刀轨最优行距计算方法研究

以五轴加工为例,对多轴加工行距提出了一套刀轨最优行距计算方法。该方法通过推导五轴加工刀具运动刃口回转面包络方程,计算相邻轨迹刀具包络面的交线,即残余凸台的顶尖线,进一步计算该线到加工曲面的距离,从而得到最大残余高度值,由此判断当前行距的优劣,据此进行进一步的搜索,最终得到最优的行距。     

200km/h动力分散型电动旅客列车组车体表面压力分布试验研究

阐述了对我国首列200km/h动力分散型电动旅客列车组(先锋号列车)车体表面压力分布测试情况,对测量结果进行了较为详细的分析,最后用流场计算软件CFX对先锋号列车周围流场进行了数值模拟计算,并将计算结果与测量结果进行了对比,两者有较好的一致性。该研究结果可为空调装置及电器设备冷却风道进排风口位置的选取提供科学依据。